Skip to content
CalContractorPrep
Menu

CSLB General Building (B) practice questions: Siding and stucco

Section 2 of 5: Framing and Structural Components

4 free practice questions on siding and stucco, part of a section that is about 20% of the General Building exam. Try each one, then open the answer: every choice is explained, and the answer names the code section or public rule it comes from.

Questions and answers

  1. 1. How must flashing at exterior window and door openings be lapped?

    Framing and Structural Components

    • A. Shingle fashion, so each upper piece laps over the piece below it
    • B. With each lower piece lapped over the piece above it
    • C. Butted edge to edge and sealed with caulk only
    • D. Ending behind the siding, short of the exterior wall finish
    Show answer

    Correct answer: A

    • A. Shingle fashion, so each upper piece laps over the piece below it

      Correct answer

      Right: shingle-fashion laps shed water outward.

    • B. With each lower piece lapped over the piece above it

      Wrong: reverse laps direct water behind the flashing.

    • C. Butted edge to edge and sealed with caulk only

      Wrong: caulked butt joints are not shingle-fashion laps.

    • D. Ending behind the siding, short of the exterior wall finish

      Wrong: the flashing must extend to the surface of the exterior wall finish.

    Explanation

    California Residential Code section R703.4 requires approved corrosion-resistant flashing at exterior window and door openings, applied shingle fashion and extending to the surface of the exterior wall finish.

  2. 2. Adhered masonry (thin stone) veneer on a stud wall ends above a paved driveway that is not supported by the house foundation. What is the minimum clearance from the bottom of the veneer to the paving?

    Framing and Structural Components

    • A. 1/2 inch
    • B. 2 inches
    • C. 4 inches
    • D. 6 inches
    Show answer

    Correct answer: B

    • A. 1/2 inch

      Wrong: 1/2 inch applies only to walking surfaces on the same foundation as the wall.

    • B. 2 inches

      Correct answer

      Right: 2 inches above paved areas.

    • C. 4 inches

      Wrong: 4 inches is the clearance above earth.

    • D. 6 inches

      Wrong: 6 inches is more than the code minimum.

    Explanation

    California Residential Code section R703.12.1 requires adhered masonry veneer on exterior stud walls to be at least 4 inches above the earth, at least 2 inches above paved areas, or at least 1/2 inch above exterior walking surfaces supported by the same foundation as the wall.

  3. 3. How many coats of exterior cement plaster are required over metal lath on a wood-frame wall where the stucco is the exposed finish?

    Framing and Structural Components

    • A. One coat
    • B. Two coats
    • C. Three coats
    • D. Four coats
    Show answer

    Correct answer: C

    • A. One coat

      Wrong: one coat does not meet the minimum.

    • B. Two coats

      Wrong: two coats are allowed only over solid bases such as masonry or concrete, or where the plaster is fully covered.

    • C. Three coats

      Correct answer

      Right: three coats over metal or wire lath.

    • D. Four coats

      Wrong: four coats are more than required.

    Explanation

    California Residential Code section R703.7.2 requires exterior cement plaster to be at least three coats over metal lath or wire lath. Two coats are allowed over masonry, concrete, treated or decay-resistant wood, or gypsum backing, or where the plaster is fully covered by veneer.

  4. 4. What is the minimum lap for fiber-cement lap siding?

    Framing and Structural Components

    • A. 3/4 inch
    • B. 1 inch
    • C. 1 1/8 inches
    • D. 1 1/4 inches
    Show answer

    Correct answer: D

    • A. 3/4 inch

      Wrong: 3/4 inch is short of the minimum.

    • B. 1 inch

      Wrong: 1 inch is the wood lap siding figure, not fiber cement.

    • C. 1 1/8 inches

      Wrong: 1 1/8 inches is short of the minimum.

    • D. 1 1/4 inches

      Correct answer

      Right: 1 1/4 inches minimum.

    Explanation

    California Residential Code section R703.10.2 requires fiber-cement lap siding (12 inches maximum width) to be lapped at least 1 1/4 inches.

Keep studying

Read the Section 2 study notes: Framing and Structural Components

All General Building topics

Study guides for this section

Test yourself

Try 25 free General Building practice questions from all five sections. Each answer explains the rule and names the code section it comes from. No sign-up.

See what the General Building exam covers