Skip to content
CalContractorPrep
Menu

CSLB General Building (B) practice questions: Seismic hardware requirements and installation

Section 2 of 5: Framing and Structural Components

4 free practice questions on seismic hardware requirements and installation, part of a section that is about 20% of the General Building exam. Try each one, then open the answer: every choice is explained, and the answer names the code section or public rule it comes from.

Questions and answers

  1. 1. A one-story house in Seismic Design Category B has its sill plates anchored to the concrete foundation with 1/2-inch anchor bolts. What is the maximum anchor bolt spacing?

    Framing and Structural Components

    • A. 6 feet on center
    • B. 8 feet on center
    • C. 10 feet on center
    • D. 12 feet on center
    Show answer

    Correct answer: A

    • A. 6 feet on center

      Correct answer

      Right: anchor bolts at not more than 6 feet on center.

    • B. 8 feet on center

      Wrong: farther than the code allows.

    • C. 10 feet on center

      Wrong: farther than the code allows.

    • D. 12 feet on center

      Wrong: farther than the code allows.

    Explanation

    California Residential Code section R403.1.6 requires sill plates to be anchored with bolts at least 1/2 inch in diameter, spaced not more than 6 feet on center, embedded at least 7 inches, placed in the middle third of the plate width, each with a nut and washer. (Tighter spacing applies to buildings over two stories in SDC D0, D1 and D2.)

  2. 2. How far may a braced wall panel be offset from its designated braced wall line?

    Framing and Structural Components

    • A. Up to 2 feet
    • B. Up to 4 feet
    • C. Up to 6 feet
    • D. Up to 10 feet
    Show answer

    Correct answer: B

    • A. Up to 2 feet

      Wrong: the code allows up to 4 feet.

    • B. Up to 4 feet

      Correct answer

      Right: the maximum offset from the braced wall line.

    • C. Up to 6 feet

      Wrong: more than the 4 feet allowed.

    • D. Up to 10 feet

      Wrong: 10 feet is the limit from each end of the line to the nearest panel, not the offset.

    Explanation

    California Residential Code section R602.10.1.2 allows braced wall panels to be offset up to 4 feet from the designated braced wall line, and the line must be placed so that no more than two-thirds of the required braced wall panel length is on one side of it.

  3. 3. A house in Seismic Design Category B has a long braced wall line with several braced wall panels. What is the maximum distance between the adjacent edges of two braced wall panels along the line?

    Framing and Structural Components

    • A. 10 feet
    • B. 12-1/2 feet
    • C. 20 feet
    • D. 25 feet
    Show answer

    Correct answer: C

    • A. 10 feet

      Wrong: 10 feet is the limit from each end of the line to the nearest panel, not between panels.

    • B. 12-1/2 feet

      Wrong: not a code value; the limit between panel edges is 20 feet.

    • C. 20 feet

      Correct answer

      Right: the maximum distance between adjacent panel edges.

    • D. 25 feet

      Wrong: 25 feet is the spacing limit between parallel braced wall lines in SDC D0 to D2, not between panels.

    Explanation

    California Residential Code section R602.10.2.2 requires the nearest edge of a braced wall panel to be within 10 feet of each end of the braced wall line, and the distance between adjacent edges of braced wall panels along the line may not exceed 20 feet.

  4. 4. What is the minimum embedment of 1/2-inch sill plate anchor bolts into a concrete foundation?

    Framing and Structural Components

    • A. 4 inches
    • B. 5 inches
    • C. 6 inches
    • D. 7 inches
    Show answer

    Correct answer: D

    • A. 4 inches

      Wrong: less than the code requires.

    • B. 5 inches

      Wrong: less than the code requires.

    • C. 6 inches

      Wrong: less than the code requires.

    • D. 7 inches

      Correct answer

      Right: at least 7 inches of embedment.

    Explanation

    California Residential Code section R403.1.6 requires anchor bolts at least 1/2 inch in diameter to be embedded at least 7 inches into concrete or grouted masonry cells.

Keep studying

Read the Section 2 study notes: Framing and Structural Components

All General Building topics

Study guides for this section

Test yourself

Try 25 free General Building practice questions from all five sections. Each answer explains the rule and names the code section it comes from. No sign-up.

See what the General Building exam covers