Skip to content
CalContractorPrep
Menu

CSLB General Building (B) practice questions: Roof framing

Section 2 of 5: Framing and Structural Components

4 free practice questions on roof framing, part of a section that is about 20% of the General Building exam. Try each one, then open the answer: every choice is explained, and the answer names the code section or public rule it comes from.

Questions and answers

  1. 1. Framers are setting trusses and installing roof sheathing on a new single-family house. Under Cal/OSHA, at what fall height must they be protected from falling?

    Framing and Structural Components

    • A. 6 feet or more
    • B. 7-1/2 feet or more
    • C. 15 feet or more
    • D. 20 feet or more
    Show answer

    Correct answer: A

    • A. 6 feet or more

      Correct answer

      Correct: section 1716.2 sets 6 feet for residential-type framing.

    • B. 7-1/2 feet or more

      7-1/2 feet is the general fall protection trigger in section 1670, not the residential framing trigger.

    • C. 15 feet or more

      15 feet is the figure in section 1669 for thrustouts and similar work, not residential framing.

    • D. 20 feet or more

      20 feet is the trigger for non-residential roofing in section 1730.

    Explanation

    Cal/OSHA Construction Safety Orders section 1716.2 requires fall protection in residential-type framing at 6 feet or more above the grade or floor below, including work on top plates, rafters and trusses and installing roof sheathing. Scaffolds, guardrails, safety nets or personal fall protection may be used.

    Source

  2. 2. What is the minimum bearing length for the end of a ceiling joist resting on a wood top plate?

    Framing and Structural Components

    • A. 1 inch
    • B. 1-1/2 inches
    • C. 2-1/2 inches
    • D. 3 inches
    Show answer

    Correct answer: B

    • A. 1 inch

      Less than the 1-1/2-inch minimum.

    • B. 1-1/2 inches

      Correct answer

      Correct: R802.6 sets 1-1/2 inches on wood or metal.

    • C. 2-1/2 inches

      More than required on wood.

    • D. 3 inches

      3 inches is the minimum on masonry or concrete, not on a wood plate.

    Explanation

    California Residential Code section R802.6 requires at least 1-1/2 inches of bearing on wood or metal for the end of each rafter or ceiling joist, and at least 3 inches on masonry or concrete.

  3. 3. Wood 2x4 rafter ties are installed instead of ceiling joists. What is their maximum spacing?

    Framing and Structural Components

    • A. 12 inches on center
    • B. 16 inches on center
    • C. 24 inches on center
    • D. 48 inches on center
    Show answer

    Correct answer: C

    • A. 12 inches on center

      Allowed, but closer than the 24-inch maximum.

    • B. 16 inches on center

      Allowed, but closer than the 24-inch maximum.

    • C. 24 inches on center

      Correct answer

      Correct: R802.5.2.2 sets 24 inches on center as the maximum.

    • D. 48 inches on center

      Too far apart; 4 feet is the collar tie spacing limit (R802.4.6) and an older-edition rafter tie figure, but R802.5.2.2 now limits rafter ties to 24 inches.

    Explanation

    California Residential Code section R802.5.2.2 requires wood rafter ties of at least 2x4 installed at no more than 24 inches on center.

  4. 4. An electrician wants to drill a hole for a cable through the web of a wood I-joist used as a rafter. When is this allowed?

    Framing and Structural Components

    • A. When the hole is no larger than one-third of the member depth
    • B. When the hole is anywhere in the middle third of the span
    • C. When the building inspector approves it in the field
    • D. Only when the manufacturer's recommendations allow it or a registered design professional has accounted for it
    Show answer

    Correct answer: D

    • A. When the hole is no larger than one-third of the member depth

      Wrong: size rules of this kind are for sawn lumber; an I-joist follows the manufacturer or a design professional (R802.7.2).

    • B. When the hole is anywhere in the middle third of the span

      Wrong: location alone does not make a hole acceptable in an engineered wood product under R802.7.2.

    • C. When the building inspector approves it in the field

      Wrong: R802.7.2 names the manufacturer's recommendations or a registered design professional, not a field approval.

    • D. Only when the manufacturer's recommendations allow it or a registered design professional has accounted for it

      Correct answer

      Correct: R802.7.2 prohibits the hole unless the manufacturer's recommendations or a registered design professional allow it.

    Explanation

    California Residential Code section R802.7.2: cuts, notches and holes in trusses, structural composite lumber, glued-laminated members, cross-laminated timber and I-joists are prohibited unless the manufacturer's recommendations allow them or a registered design professional has specifically considered their effect in the member design.

Keep studying

Read the Section 2 study notes: Framing and Structural Components

All General Building topics

Study guides for this section

Test yourself

Try 25 free General Building practice questions from all five sections. Each answer explains the rule and names the code section it comes from. No sign-up.

See what the General Building exam covers