Skip to content
CalContractorPrep
Menu

Jobsite Traffic Control in California: CA MUTCD Flaggers, Signs and Tapers

Section 5 of 5, about 15% of the B exam

Updated

When work on or next to a public street puts workers at risk from traffic, Cal/OSHA requires traffic controls that conform to the California MUTCD (8 CCR §1598). The manual sets the numbers: on urban streets the first warning sign goes about 4 to 8 times the speed limit (in feet) ahead of the work (CA MUTCD §6B.04); a merging taper is W × S² ÷ 60 at 40 mph or less and W × S at 45 mph or more (CA MUTCD §6B.08); cones are at least 28 inches high at night (CA MUTCD §6K.03); and a flagger uses a STOP/SLOW paddle, with flags for emergencies only (CA MUTCD §6D.03).

This guide walks through a work zone the way a driver meets it: the four areas, the signs, the tapers, the cones and other devices, and the flaggers. Each rule names its section, and each formula has a worked example.

Which manual

Caltrans' current manual is the CA MUTCD 2026, effective January 18, 2026. It replaced the 2014 edition, and Part 6 (temporary traffic control) is now lettered 6A to 6P: flaggers are Chapter 6D, one-lane two-way control 6E, signs 6F to 6I, channelizing devices 6K and arrow boards 6L. CSLB's B study guide (March 2026) still lists the 2014 edition, so section numbers in older books may not match the ones below, which are from the 2026 manual. The rules covered here are the current ones.

When traffic control is required

  • Cal/OSHA. Where traffic or hauling at a job that encroaches on a public street or highway creates a hazard to workers, use a system of traffic controls that conforms to the California MUTCD. (8 CCR §1598)
  • Visible workers, Cal/OSHA. Workers on foot exposed to traffic wear high-visibility vests, jackets or shirts. At night the garments are retroreflective and visible from at least 1,000 feet. (8 CCR §1598)
  • Visible workers, CA MUTCD. All workers in a temporary traffic control zone within the right-of-way, day or night, wear apparel meeting Performance Class 2 or 3 of ANSI/ISEA 107, in fluorescent orange-red, fluorescent yellow-green or a mix. (CA MUTCD §6C.05)

The four areas of a work zone

A temporary traffic control zone runs from the first warning sign (or flashing vehicle lights) to the END ROAD WORK sign or the last device. It has four areas, in the order a driver reaches them: (CA MUTCD §6B.03)

  1. Advance warning area: tells drivers what is ahead.
  2. Transition area: moves traffic out of its normal path, usually with a taper.
  3. Activity area: where the work happens.
  4. Termination area: lets traffic return to its normal path.

The activity area holds the work space, the traffic space where vehicles pass, and the buffer space that separates them. Keep work, equipment, vehicles and materials out of the buffer space. (CA MUTCD §6B.06)

Advance warning signs

Distance to the first sign

Road Sign nearest the work, ahead of it Source
Urban street About 4 to 8 times the speed limit, in feet CA MUTCD §6B.04
Rural highway About 8 to 12 times the speed limit, in feet CA MUTCD §6B.04

Example: On a 35 mph urban street, 4 × 35 = 140 and 8 × 35 = 280, so the sign nearest the work goes about 140 to 280 feet ahead.

  • Spacing between signs. The recommended minimum is 100 feet on low-speed urban streets (25 mph or less) and 500 feet on rural roads. On a low-speed residential street with a single sign, the advance warning area may be as short as 100 feet. These are guidance values that engineering judgment may adjust. (CA MUTCD §6B.04)
  • When advance warning may be left out. In California, when the activity area is behind a barrier, more than 2 feet behind the curb, or 15 feet or more from the edge of the traveled way. (CA MUTCD §6B.04)

Sign height

  • In business, commercial or residential areas where parking or pedestrians are likely, and over sidewalks, the bottom of a roadside sign is at least 7 feet above the top of the curb, or above the near edge of the traveled way where there is no curb. (CA MUTCD §6F.02)
  • In rural areas, at least 5 feet above the near edge of the pavement. (CA MUTCD §6F.02)
  • On barricades or other portable supports, at least 1 foot above the traveled way. Signs normally go on the right side of the road. (CA MUTCD §6F.02)

Tapers

A taper is a line of devices set at an angle to move traffic out of its lane. The basic length L depends on the offset width W in feet and the speed S in mph. (CA MUTCD §6B.08)

Speed Merging taper length L Source
40 mph or less W × S² ÷ 60 CA MUTCD §6B.08
45 mph or more W × S CA MUTCD §6B.08

The other tapers are figured from L: (CA MUTCD §6B.08)

Taper Length Source
Merging At least L CA MUTCD §6B.08
Shifting About 1/2 L CA MUTCD §6B.08
Shoulder About 1/3 L CA MUTCD §6B.08
Downstream 50 feet minimum, 100 feet maximum CA MUTCD §6B.08
One-lane, two-way (flagger) 50 feet minimum, 100 feet maximum CA MUTCD §6B.08

Example 1: A 12-foot lane closed at 25 mph: 12 × 25 × 25 ÷ 60 = 12 × 625 ÷ 60 = 125 feet.

Example 2: A 12-foot lane closed at 55 mph: 45 mph or more, so L = 12 × 55 = 660 feet.

Example 3: A shifting taper for a 12-foot lane at 40 mph: L = 12 × 1,600 ÷ 60 = 320 feet, and half of that is 160 feet.

Pick the formula by the speed first. At 40 mph or less, square the speed and divide by 60; at 45 mph or more, multiply width by speed.

Cones, drums and other devices

Spacing

Space channelizing devices no farther apart, in feet, than 1 times the speed limit along a taper and 2 times the speed limit along a tangent (the straight run beside the work). California's Table 6K-101(CA) of maximum spacings also applies. (CA MUTCD §6K.01)

Example: On a 35 mph street, cones in the taper are no more than 35 feet apart and along the tangent no more than 70 feet apart.

The devices

Device Key rules Source
Cones Mostly orange; at least 18 inches high for daytime on low-speed roads; at least 28 inches on freeways and high-speed roads and at night on any highway; retroreflectorized or lighted at night CA MUTCD §6K.03
Tubular markers Mostly orange, at least 18 inches high and 2 inches wide facing traffic; 28 inches where cones must be CA MUTCD §6K.04
Vertical panels Orange and white stripes sloping down at 45 degrees toward the side traffic passes CA MUTCD §6K.05
Drums Lightweight and deformable, at least 36 inches high and 18 inches wide; horizontal orange and white stripes with the top stripe orange; metal drums may not be used CA MUTCD §6K.06
Barricades Rail stripes slope down at 45 degrees in the direction road users are to pass; Type 1 and 2 at least 24 inches long, Type 3 at least 48 inches CA MUTCD §6K.07
Arrow boards Arrow or chevron mode only for lane closures on multi-lane roads; caution mode only for shoulder work or closing one lane of a two-lane, two-way road CA MUTCD §6L.06

(CA MUTCD Chapter 6K, CA MUTCD §6L.06)

Flaggers

When and who

  • When. Cal/OSHA requires flaggers where barricades and warning signs cannot control moving traffic. (8 CCR §1599)
  • Training first. A flagger is trained in the fundamentals of flagging moving traffic before being assigned, and the training is documented. (8 CCR §1599) Under the CA MUTCD, qualified persons give the training, which covers equipment, station layout, the stop, proceed and slow signals, emergency vehicles and hostile drivers, and it is documented under the employer's Injury and Illness Prevention Program. (CA MUTCD §6D.01)
  • The station. Place it so drivers have room to stop, with advance warning signs ahead except in emergencies. At night the station is lit so the flagger is clearly visible. (CA MUTCD §6D.06, 8 CCR §1599)

The paddle and the flag

  • The STOP/SLOW paddle is the primary hand-signaling device. It is octagonal, on a rigid handle, retroreflectorized for night use and at least 18 inches wide; a 24-inch paddle may be used where more emphasis is needed and speeds are 30 mph or more. (CA MUTCD §6D.02)
  • In California, a flag is for emergencies only. It is red or fluorescent orange-red, at least 24 inches square, on a staff about 36 inches long. (CA MUTCD §6D.03)

Signals

To stop traffic, the flagger faces road users, holds the STOP face toward them with the arm extended straight out from the body, and raises the free hand, palm toward traffic, above shoulder level. The flagger stands on the shoulder next to the controlled lane or in the closed lane, steps into the open lane only after traffic has stopped, and stands alone, away from other workers and equipment. (CA MUTCD §6D.05)

One-lane, two-way traffic

When both directions share one lane, flaggers work at each end, one of them the coordinator, and they communicate orally, electronically or with hand signals that cannot be mistaken for flagging signals. A single flagger may control a stretch short enough to see end to end. (CA MUTCD §6E.02) A pilot car carries a PILOT CAR FOLLOW ME or PILOT CAR DO NOT PASS sign. (CA MUTCD §6E.04) The flag transfer method, where the last driver carries a flag to the far end, may not be used in California. (CA MUTCD §6E.03)

Traps to watch for

  • Which formula? At 40 mph or less, square the speed and divide by 60. At 45 mph or more, multiply. Using the wrong one is the most common taper mistake.
  • Taper or tangent? Device spacing is 1 times the speed limit on a taper and 2 times on a tangent.
  • 28 inches at night. Daytime 18-inch cones are only for low-speed roads; at night every highway needs 28-inch cones.
  • Flags are not normal flagging tools in California. The paddle is; a flag is for emergencies.
  • Old section numbers. Books based on the 2014 manual use different section numbers; the numbers here are from the CA MUTCD 2026.
  • 1,000 feet. Cal/OSHA's night garment rule is about visibility distance, not sign distance.

How to use this guide

Work the taper and spacing examples by hand with different widths and speeds until picking the formula is automatic, then learn the device heights and the flagger rules. Then answer the practice questions below this guide. Pedestrian protection next to a job, hauling loads on public roads and the other Safety subtopics are in our B exam safety notes.

Read the Section 5 study notes: Safety

Practice questions

Think of your answer first, then open the explanation.

  1. 1. Under Cal/OSHA, what must happen before a worker is assigned as a flagger?

    Safety

    • A. The worker must be trained in the fundamentals of flagging, and the training must be documented
    • B. Nothing, if the worker has a driver's license
    • C. The worker must be at least 21 years old
    • D. The worker must hold a Caltrans flagger license
    Show answer

    Correct answer: A

    • A. The worker must be trained in the fundamentals of flagging, and the training must be documented

      Correct answer

      Correct: documented flagger training before assignment (section 1599).

    • B. Nothing, if the worker has a driver's license

      Wrong: a driver's license is not flagger training.

    • C. The worker must be at least 21 years old

      Wrong: section 1599 sets no age requirement.

    • D. The worker must hold a Caltrans flagger license

      Wrong: section 1599 calls for training, not a Caltrans license.

    Explanation

    Title 8 section 1599 requires flaggers to be trained in the fundamentals of flagging moving traffic before being assigned as flaggers, with the training documented.

  2. 2. Under the California MUTCD, when may a flagger use a red flag instead of a STOP/SLOW paddle to control traffic?

    Safety

    • A. Only in emergency situations
    • B. Any time during daylight hours
    • C. On roads with speeds of 25 mph or less
    • D. Whenever the flagger works alone
    Show answer

    Correct answer: A

    • A. Only in emergency situations

      Correct answer

      Correct: in California, flags are limited to emergency situations (section 6D.03).

    • B. Any time during daylight hours

      Wrong: daylight does not permit flags; the paddle is the device for normal flagging.

    • C. On roads with speeds of 25 mph or less

      Wrong: road speed does not permit flags in California.

    • D. Whenever the flagger works alone

      Wrong: a single flagger still uses the paddle; flags are for emergencies only.

    Explanation

    The STOP/SLOW paddle is the primary hand-signaling device (California MUTCD section 6D.02). California section 6D.03 limits the use of flags to emergency situations; when used, a flag must be red or fluorescent orange-red, at least 24 inches square, on a staff about 36 inches long.

    Source

  3. 3. A crew sets up work on an urban street with a 30 mph speed limit. Under the California MUTCD guidance, about how far from the work zone should the advance warning sign nearest the work be placed?

    Safety

    • A. 30 to 60 feet
    • B. 120 to 240 feet
    • C. 240 to 360 feet
    • D. 500 to 1,000 feet
    Show answer

    Correct answer: B

    • A. 30 to 60 feet

      Wrong: this is 1 to 2 times the speed limit.

    • B. 120 to 240 feet

      Correct answer

      Correct: 4 to 8 times 30 mph = 120 to 240 feet.

    • C. 240 to 360 feet

      Wrong: this is 8 to 12 times the speed, the rural guidance.

    • D. 500 to 1,000 feet

      Wrong: much farther than the urban guidance.

    Explanation

    California MUTCD section 6B.04 guidance places the warning sign nearest the work zone on urban streets at a distance in feet of about 4 to 8 times the speed limit in mph (about 8 to 12 times on rural highways). 4 x 30 = 120 feet and 8 x 30 = 240 feet.

  4. 4. A temporary ROAD WORK AHEAD sign is mounted at the roadside on a residential street where people park and walk. Under the California MUTCD, the bottom of the sign must be at least how high above the top of the curb (or, where there is no curb, the near edge of the traveled way)?

    Safety

    • A. 1 foot
    • B. 3 feet
    • C. 5 feet
    • D. 7 feet
    Show answer

    Correct answer: D

    • A. 1 foot

      Wrong: 1 foot applies only to signs on barricades or other portable supports.

    • B. 3 feet

      Wrong: below the minimum.

    • C. 5 feet

      Wrong: 5 feet is the rural minimum.

    • D. 7 feet

      Correct answer

      Correct: 7 feet in residential areas with parking or pedestrians (6F.02).

    Explanation

    California MUTCD section 6F.02 requires roadside temporary traffic control signs in business, commercial or residential areas where parking or pedestrians are likely to have the bottom at least 7 feet above the top of the curb (or the near edge of the traveled way where there is no curb). In rural areas the minimum is 5 feet above the near edge of the pavement. Signs on barricades or other portable supports must be at least 1 foot above the traveled way.

  5. 5. A lane 11 feet wide is closed on a road with a posted speed of 30 mph. Using the California MUTCD formula, what is the minimum length of the merging taper?

    Safety

    • A. 110 feet
    • B. 165 feet
    • C. 330 feet
    • D. 495 feet
    Show answer

    Correct answer: B

    • A. 110 feet

      Wrong: this is 11 x 10.

    • B. 165 feet

      Correct answer

      Correct: 11 x 900 / 60 = 165 feet.

    • C. 330 feet

      Wrong: this uses L = W x S, the formula for 45 mph or more.

    • D. 495 feet

      Wrong: this divides by 20 instead of 60.

    Explanation

    California MUTCD section 6B.08: for speeds of 40 mph or less, L = W x S x S / 60. L = 11 x 30 x 30 / 60 = 11 x 900 / 60 = 165 feet. A merging taper is at least L long.

  6. 6. A 10-foot paved shoulder is closed on a highway with a posted speed of 45 mph. Using the California MUTCD taper guidance, about how long should the shoulder taper be?

    Safety

    • A. 75 feet
    • B. 150 feet
    • C. 225 feet
    • D. 450 feet
    Show answer

    Correct answer: B

    • A. 75 feet

      Wrong: 75 feet is one-sixth of L.

    • B. 150 feet

      Correct answer

      Correct: L = 10 x 45 = 450 feet; one-third of L = 150 feet (section 6B.08).

    • C. 225 feet

      Wrong: 225 feet is one-half of L, the length for a shifting taper.

    • D. 450 feet

      Wrong: 450 feet is the full L, the length for a merging taper.

    Explanation

    California MUTCD section 6B.08: at 45 mph or more, L = W x S = 10 x 45 = 450 feet. A shoulder taper should be about one-third of L: 450 / 3 = 150 feet.

    Source

  7. 7. Cones line a straight (tangent) section of a lane closure on a 40 mph road. Under the general spacing guidance in California MUTCD section 6K.01, the cones should be no farther apart than:

    Safety

    • A. 20 feet
    • B. 40 feet
    • C. 80 feet
    • D. 120 feet
    Show answer

    Correct answer: C

    • A. 20 feet

      Wrong: 20 feet is half the speed figure; the general tangent maximum is 2 x 40 = 80 feet (California's 20-foot figure at 40 mph is only for sections with missing or conflicting pavement markings).

    • B. 40 feet

      Wrong: 1 x speed is the taper spacing, not the tangent spacing.

    • C. 80 feet

      Correct answer

      Correct: 2 x 40 = 80 feet on a tangent.

    • D. 120 feet

      Wrong: 3 x speed is beyond the guidance.

    Explanation

    California MUTCD section 6K.01 says the spacing of channelizing devices should not exceed a distance in feet equal to the speed limit in mph along a taper, or twice the speed limit in mph along a tangent. 2 x 40 = 80 feet. California's Table 6K-101(CA) gives the same 80-foot tangent maximum at 40 mph.

  8. 8. Cones will be used to close a lane on a highway at night. Under the California MUTCD, what is the minimum cone height?

    Safety

    • A. 12 inches
    • B. 18 inches
    • C. 24 inches
    • D. 28 inches
    Show answer

    Correct answer: D

    • A. 12 inches

      Wrong: below any height in the rule.

    • B. 18 inches

      Wrong: 18 inches is allowed only for daytime use on low-speed roads.

    • C. 24 inches

      Wrong: not the figure in the rule.

    • D. 28 inches

      Correct answer

      Correct: at least 28 inches at night (6K.03).

    Explanation

    California MUTCD section 6K.03 requires cones at least 28 inches high on freeways and other high-speed highways, at night on any highway, or where more conspicuous guidance is needed. Cones at night must be retroreflectorized or lighted.

Test yourself

Try 25 free General Building practice questions from all five sections. Each answer explains the rule and names the code section it comes from. No sign-up.

See what the General Building exam covers